潜水渣浆泵作业注意事项

潜水渣浆泵工作时，潜水泥砂泵需要放在陆地上，吸水管放在水中，还需要灌泵启动。泥浆泵和液下渣浆泵由于受到结构的限制，工作时电机需要放在水面之上，潜水吸沙泵放入水中，因此必须固定，否则，电机掉到水中会导致电机报废。而且由于长轴长度一般固定，所以耐磨潜水渣浆泵安装使用较麻烦，应用的场合受到很多的限制。如果有备用泵，好两台泵轮流使用。如果卡泵就只有修泵了，可以在进水口加一张网，不让过多的杂质进到泵里，这样卡泵的机率就会小很多！

潜水吸砂泵 潜水吸沙泵 潜水泥浆泵 潜水矿浆泵 潜水尾矿泵

潜水吸砂泵 潜水吸沙泵 潜水泥浆泵 潜水矿浆泵 潜水尾矿泵

渣浆泵生产厂家，主要产品有渣浆泵、脱硫泵、砂砾泵、泥浆泵、杂质泵、污水泵、泡沫泵、双吸泵等渣浆泵配件及渣浆泵成套产品。

一般杂质泵的叶轮用平行盖板，浆体进入叶轮后，在出口处向两侧形成外旋涡，使叶轮的前后盖板和内衬严重磨损，这是造成过流部件寿命短的主要原因，而ZJA系列渣浆泵充分吸收了ZJ系列渣浆泵和沃曼泵的优点，设计的叶轮在出口处形成凹形，使叶轮两侧前后盖板处的速度大于中间速度，浆体在出口处分为两股流体，向中心旋转，迫使颗粒向中心流动造成内旋涡状，使两侧的浓度降低，从而减轻了泵体流道和两侧壁的磨损。Submersible slurry pump operation matters needing attention submersible slurry pump work, submersible cement sand pump needs to be put on the land, suction pipe in the water, but also need to start the pump. Because of the structure limitation of the mud pump and the slurry pump, the motor needs to be put on the water surface when they work, and the sand suction pump for diving must be fixed, otherwise, the motor will be discarded when it falls into the water. And because the length of the long shaft is generally fixed, so wear-resistant submersible slurry pump installation and use more trouble, application of the occasion by a lot of restrictions. If there is a backup pump, good two pumps in turn use. If the card pump only repair the pump, you can add a net in the inlet, do not let too many impurities into the pump, so the card pump will be much less! Submersible sand pump, submersible sand pump, submersible slurry pump, submersible mineral slurry pump, submersible tailings pump sand pump, submersible sand pump, submersible slurry pump, submersible slurry pump, submersible tailings pump slurry pump, submersible slurry pump, slurry pump manufacturers, the main products are slurry pump, desulphurization pump, gravel pump, slurry pump, impurity pump, sewage pump, foam pump, double suction pump and other slurry pump accessories and slurry pump complete sets of products. Generally, the impellers of the impellers of the impellers use parallel cover plates. After the slurry enters the impellers, it forms outer vortices to both sides at the outlet, which causes the front and rear cover plates and the inner lining of the impellers to wear seriously. This is the main reason for the short service life of the overflow parts, while Zja series slurry pumps fully absorb the advantages of ZJ series slurry pumps and Wurman pumps, the designed impeller is concave at the outlet, which makes the speed at the front and rear cover plates on both sides of the impeller greater than the middle speed, and the slurry is divided into two fluids at the outlet, rotating toward the center forces the particles to flow toward the center to create an inner vortex, which reduces the concentration on both sides, thus reducing the flow channel and the wear of both sides of the pump body.